سبلة عمان

Go Back   سبلة عمان » سبلة اللغة الإنجليزية

Notices

 
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09/10/2010, 01:49 PM
البحير's Avatar
البحير البحير is offline
عضو نشيط
 
Join Date: May 2010
Location: المضيبي
Gender: ذكر
Posts: 100
Question some one to translate this steps?

es300 procedures to turn off the day running light:

النص الانجليزي يقول:
Procedure:
1) Make sure everything is working to begin with. Start the engine, release the parking brake, and with the headlamps to "Off", make sure both high beams are ON at low intensity.
Turn the switch to "Parking Lights". 2 small bulbs above the High Beams should also come on, as well as the tail lamps. Turn the switch to "Headlamps". The Low beams should come On, and the low intensity High beams should turn Off. Note that the 2 small bulbs in the High Beam housing are still On (these are the front Parking Lights) Toggle the Dimmer to High Beams. The High Beams should both come on at Full intensity. Now turn Lights and Engine Off.

2) Open the Hood. Remove the Black Panel covering the Right Side (of the car) Engine Compartment (4 fasteners). Push the fastener center dot to release. DO NOT lose the fasteners in the engine bowels! Set the fasteners aside, and remove the cover and set aside.

3) On the Right Inner Fender is a rectangular Black Box labeled "Relay". Open the top by using a small screwdriver to gently pry the end locks. Set the top aside. Inside are 2 Relays.

4) Remove the FRONT Relay by gently pulling it out. Note that it has 5 Contacts. 3 in a Row, and 2 on the other side. Set it aside.

5) Restart the engine. Confirm that the DRL are off. Turn on the Headlamps and Toggle the High Beam. Confirm that the LH High Beam is ON, and the RH High Beam is OFF. This insures that you at the correct Relay. Turn the Engine and Lights Off.

6) Gently Remove the Other Relay from the Box as well, and set it aside. It has a different Prong configuration. Gently pull the Relay Box up and off of its mounting. Gently extend the Wiring Harness leading to it to give yourself some slack.

7) Open the Bottom of the Relay Box by gently Prying the locks. It will pivot open on one edge.
Turn the entire Relay Box over to see the Wiring inside.

8) The Front Relay has 5 wires leading to it. Orange, Turquoise, Blue, and 2 White/Black Stripe.
Note that Turquoise , Blue, and 1 White/Black Stripe are Thicker in Diameter. The Orange and the other White/Black Stripe are thinner.

9) Find the Thicker White/Black Stripe Wire. It should lead to the Center Contact of the 3 in a Row set. THIS IS YOUR TARGET.

10) For a permanent fix, you can cut the wire. I HIGHLY recommend you proceed in a reversible fashion. This way you or the next owner can reinstate the DRL easily.

11) Turn the Relay Box upright. To remove the Center Contact of the 3 in a Row, use the Miniature Screwdriver or the Metal Shim to Release the locking Pin of the Contact. This is the only tricky part, and is easy after you have done it once and can see how the Contact locks in place.

12) Look at the Contact from above. It has a Flat side, and a Rounded Side. Slide the Shim or Miniature Screwdriver down the Middle of the Rounded Side against the plastic. Stay in the Middle, You will meet an obstruction (the locking Pin). Push the screwdriver or shim through and GENTLY pull the thicker White/Black Stripe wire from the backside. The wire and Contact should come out of the Box. If it does not, repeat the process. It does NOT take Brute Force.

13) With the Contact free of the Housing, wrap the metal with electricians tape for insulation.
Fold the wire into the Relay Box, and Close the Bottom. Make sure both sides snap in place.
Reset the Relay Box in its Mounting on the Inner Fender.

14) Replace both Relays, pushing them firmly in place. The Front Relay is still needed for the RH High Beam. Replace the Relay Box Cover, making sure both ends snap in place.

15) Replace the Right Engine Cover and 4 fasteners. To Reset the Fasteners, Gently separate the 2 legs until the center Dot can be pushed back up from the bottom to a protruding postion. This is also tricky until you have done it once. Just be gentle. With the Dots protruding, insert the fastener and click the Dot down part way. This will lock the Engine Cover in place.

16) Start the Engine. The DRL should be Off. Go through all positions of the Light Switch and Dimmer to make sure both Low and High Beams on L and R sides come On as they should.

That's it. Make sure you have retrieved all your tools from the Engine Compartment, close the Hood, and enjoy your work.

This Process should work on all US RX 330, RX350, and RX400, in that the Headlight wiring is the same. It will work on Standard and Xenon Low Beams. Please let me know if you discover any Kinks. I have looked only at US wiring diagrams, so I cannot say with certainty if things are the same in Canada, Europe, and Asia.

Note that I have repeatedly used the word "Gently" Plastic will break, and new Lexus parts are expensive.
[/SIZE]
  Advertisement Post
  #2  
Old 09/10/2010, 03:02 PM
الفوتوغرافي's Avatar
الفوتوغرافي الفوتوغرافي is offline
خاطر
 
Join Date: Sep 2010
Location: الرستاق
Gender: ذكر
Posts: 41
Default

It is too hard to find some one does this for you. But, I have a solution that might helps you a little bit. Click on this link to find the answer... http://www.mr-sa.com/Translate/index.php
__________________
Marwan K. A.
  #3  
Old 10/10/2010, 10:23 AM
البحير's Avatar
البحير البحير is offline
عضو نشيط
 
Join Date: May 2010
Location: المضيبي
Gender: ذكر
Posts: 100
Default

help help i need this
  #4  
Old 10/10/2010, 03:34 PM
الفوتوغرافي's Avatar
الفوتوغرافي الفوتوغرافي is offline
خاطر
 
Join Date: Sep 2010
Location: الرستاق
Gender: ذكر
Posts: 41
Default

What can I do for you, bro? I gave you my support as possible I could. Sorry.
__________________
Marwan K. A.
 

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Easy Steps to Bring Meditation Into Daily Life اميرة ف مملكتي الصغيرة سبلة اللغة الإنجليزية 7 10/10/2010 12:51 PM
25 Steps To Be Closer To Allah miss mughairi سبلة اللغة الإنجليزية 2 04/08/2010 02:14 PM
مطلوب SIDE STEPS للأودي Q7 oman mac قسم طلبات شراء المركبات ولوازمها 3 15/06/2010 06:35 PM
THE KEY STEPS TO A SUCCESSFULL JOB HUNTING THE SHED سبلة اللغة الإنجليزية 1 22/05/2010 08:25 AM
Nine Steps to Success e7sas سبلة اللغة الإنجليزية 7 18/06/2007 07:03 PM



All times are GMT +4. The time now is 12:09 PM.

تحت إشراف السبلة للحلول الرقمية ش.م.م
s-oman.net :: Eighth Year, Day 298
لا تمثل المواضيع المطروحة في سبلة عُمان رأيها، إنما تحمل وجهة نظر كاتبها